"aarcuda69062" <nonelson@[EMAIL PROTECTED]
> wrote in message
news:nonelson-40B786.23161219032008@[EMAIL PROTECTED]
> In article <UaKdnct1q_DSHHzanZ2dnUVZ_v6rnZ2d@[EMAIL PROTECTED]
>,
> "maxpower" <damnnickname@[EMAIL PROTECTED]
> wrote:
>
> > "aarcuda69062" <nonelson@[EMAIL PROTECTED]
> wrote in message
> > news:nonelson-8CC7D5.22321118032008@[EMAIL PROTECTED]
> > > In article <MLGdndl036D1TEPanZ2dnUVZ_jmdnZ2d@[EMAIL PROTECTED]
>,
> > > "maxpower" <damnnickname@[EMAIL PROTECTED]
> wrote:
> > >
> > > > "Bruce" <dg_brousard@[EMAIL PROTECTED]
> wrote in message
> > > > news:Xns9A64A41ECBD41dgbrousardyahoocom@[EMAIL PROTECTED]
> > > > > "maxpower" <damnnickname@[EMAIL PROTECTED]
> wrote in
> > > > > news:Zo6dnetP9raENkbanZ2dnUVZ_ommnZ2d@[EMAIL PROTECTED]
> > > > >
> > > > > >
> > > > > > "Bruce" <dg_brousard@[EMAIL PROTECTED]
> wrote in message
> > > > > > news:Xns9A61D1249FAD0dgbrousardyahoocom@[EMAIL PROTECTED]
> > > > > >> Got part, Dealer said Crank positioned senor was behind the
power
> > > > > >> steering pump on the right side of motor, and I would have to
pull
> > > > > >> power steering pump bracket. It took 2 hours to remove the
pump
and
> > > > > >> bracket, and the
> > > > > > upper
> > > > > >> and lower plastic cover over the cam shaft belt. Could not
find
> > Crank
> > > > > >> positioned senor! Called a local garage, and was told the
senor
was
> > > > > >> on other side of motor, over the starter! It was there! Put
part
> > in,
> > > > > >> Started fine, Ran OK for 5 miles, then it cut off the Cruise
> > Control
> > > > > >> by its self and motor started cutting out (Missing). I will
try
to
> > > > > >> get a new error
> > > > > > code
> > > > > >> soon. Any Ideas?
> > > > > >
> > > > > >
> > > > > >
> > > > > > Your gonna have to get out your DVO meter and start doing
checks
> > while
> > > > > > you wiggle wires. Since it is an intermittent problem you may
have a
> > > > > > hard time finding it unless you see a shorted wire in the
harness or
> > > > > > bad pin in a connector. Is this a 2 or four door Stratus?
> > > > > >
> > > > > > Glenn
> > > > > >
> > > > > >
> > > > >
> > > > > It's a 4 door, I'm now getting an error code 0300 Could it be
the
> > spark
> > > > > plug wires? They look good and the problems comes and goes. It's
> > > > > starting fine now, just starts missing while driving.
> > > > > Thanks for your help
> > > > > Bruce
> > > >
> > > >
> > > > A P0300 is a random cylinder misfire and could be almost anything
from
> ^^^^^^
> > > > fuel problems to plugs and wires, clogged exhaust you name it!!
> > > >
> > > > Glenn
> > >
> > > Fixed it for ya.
> >
> > Lost me?
Our books are written as a multiple meaning more then one. Random is one
or
the other. The fault code in the diagnostic book say's "P0300 as a
multiple
cylinder misfire" meaning more then one
|
