"Bret Ludwig" <bretldwig@[EMAIL PROTECTED]
> wrote in message
news:6329c19f-1c81-4c9d-b9d0-8546eb394f1a@[EMAIL PROTECTED]
>
>>
>> > >> >> >> Does anyone no how to disable the automatic door locks that
>> > >> >> >> lock
>> to
>> > >> >> >> doors once you reach about 15mph on a 1993 Plymouth Grand
>> Voyager?
>> > > The
>> > >> >> >> stupid things are driving me crazy, I use it to make
>> > >> >> >> delievries
>> and
>> > >> >> >> have to keep unlocking the door every time I pull away from
a
>> stop.
>>
>> > >> >> >> Help please!!!
>>
>> > >> >> > A scan tool would be needed to go into the Body Control
Module
>> > >> >> > to
>> > > have
>> > >> >> > this
>> > >> >> > done.
>>
>> > >> >> > Glenn Beasley
>> > >> >> > Chrysler Tech
>>
>> > >> >> Does it?
>>
>> > >> >> Im sure it tells you how in my haynes or handbook somewhere. It
>> > >> >> is
>> > >> >> very
>> > >> >> annoying so I will dig it out asap and check it out for myself.
>>
>> > >> > Haynes Book!!! Are you kidding?
>>
>> > >> N. Its either in there or in the handbook! Somewhere. I am sure I
>> > >> read
>> it
>> > >> already...
>>
>> > > Its a customer Preference setting that was designed to be set by a
>> > > scan
>> > > tool
>> > > only.
>>
>> > > Glenn Beasley
>> > > Chrysler Tech
>>
>> > When I think about it it may have said it was "turnoffable" but that
>> > you
>> > should contact your dealer?
>> > I was actually looking to find out how to program a third key for my
>> > 2007
>> > Dodge Caravan. The details for that were there for sure,
>>
>> That's correct, Chrysler made it so that the owner would have to bring
it
>> in
>> to the dealer to have the settings changed on the older model vehicles
>
> Just disconnect the solenoid.
I knew I read it somewhere!!!
Here is how:
The Automatic Door Locks can be enabled or disabled by performing the
following procedure:
1. Close all doors and place the key in the ignition switch.
2. Cycle the ignition switch ON/OFF four times ending i in the OFF
position,
(do not start the engine)
3. Within 10 seconds of the final cycle, press the interior driver's door
lock switch to the LOCK position.
4. A single chime will sound to signify that you have successfully
completed
the programming.
You can turn the feature back on by repeating the above mentioned
procedure
or by performing the procedure in the Electronic Vehicle Information
Center
(EVIC), Customer Programmable Features section on vehicles so equipped.
________________________________________________________________
And a few more for fun!
Customer Key Programming
You can program new sentry keys to the system if you have two valid sentry
keys by performing the following procedure:
1. Cut the additional Sentry Key Transponder blank(s) to match the
ignition
switch lock cylinder key code.
2. Insert the first valid key into the ignition switch and turn the
ignition
switch ON for at least 3 seconds but no longer than 15 seconds. Turn the
ignition switch OFF and remove the first key.
3. Insert the second valid key and turn the ignition switch ON within 15
seconds. After ten seconds a chime will sound and the Theft Alarm Light
will
begin to flash. Turn the ignition switch OFF and remove the second key.
4. Insert a blank Sentry Key into the ignition switch and turn the
ignition
switch ON within 60 seconds. After 10 seconds a single chime will sound.
The
Theft Alarm Light will stop fla****ng, turn on for 3 seconds; then turn
off.
The new Sentry Key has been programmed. The Keyless Entry Transmitter will
also be programmed during this procedure.
Repeat this procedure to program up to a total of 8 keys. If you do not
have
a programmed sentry key, contact your dealer for details.
NOTE: If a programmed key has been lost, see your dealer to have all
remaining keys erased from the systems memory. The remaining keys must
then
repro-grammed. This will prevent the lost key from starting your vehicle.
All vehicle keys must be taken to the dealer at the time of service to be
reprogrammed.
The Remote Unlock Driver's Door 1st feature can be enabled or disabled by
performing the following procedure:
1. Press the UNLOCK button for 5 to 10 seconds.
2. While the UNLOCK button is pressed, (after 5 seconds) press the LOCK
button. Release both buttons.
The "Remote Unlock Driver's Door 1st" feature can be reactivated by
repeating the above mentioned procedure or by performing the procedure in
the Electronic Vehicle Information Center (EVIC), Customer Programmable
Features section on vehicles so equipped.
If desired, the "Sound Horn On Lock" feature can be turned on and off by
performing the following procedure:
1. Press the LOCK button for 5 to 10 seconds.
2. While the LOCK button is pressed (after 5 seconds), press the PANIC
button. Release both buttons.
The "Sound Horn On Lock" feature can be reactivated by repeating this
procedure or by performing the procedure in the Electronic Vehicle
Information Center (EVIC), Customer Programmable Features section on
vehicles so equipped.
To Turn Off "Flash Lights On Lock/Unlock" - If Equipped
If desired, the "Flash Lights On Lock/Unlock" feature can be turned on and
off by performing the following procedure:
1. Press the LOCK button for 5 to 10 seconds.
2. While the LOCK button is pressed, (after 5 seconds) press the UNLOCK
button. Release both buttons.
The "Flash Lights On Lock/Unlock" feature can be reactivated by repeating
this procedure or by performing the procedure in the Electronic Vehicle
Information Center (EVIC), Customer Programmable Features section on
vehicles so equipped. The table below explains the Lamp Flash options.
The Sliding Door Open Flash can be enabled or disabled by performing the
following procedure:
1. Place the key in the ignition switch.
2. Cycle the ignition switch ON/OFF four times ending in the OFF position,
(do not start the engine)
3. Within 10 seconds of the final cycle, press the hazard switch.
4. A single chime will sound to signify that you have successfully
completed
the programming.
You can turn the feature back on by repeating the above mentioned
procedure
or by performing the procedure in the Electronic Vehicle Information
Center
(EVIC), Customer Programmable Features section on vehicles so equipped.
Enhanced Driver Seat Belt Use Reminder System (BeltAlert)
If the driver's seat belt has not been buckled within 60 seconds of
starting
the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the
Enhanced Warning System (BeltAlert) will alert the driver to buckle their
seat belt. The driver should also instruct all other occupants to buckle
their seat belts. Once the warning is triggered, the Enhanced Warning
System
(BeltAlert) will continue to chime and flash the Seat Belt Warning Light
for
96 seconds or until the driver's seat belt is buckled.
The Enhanced Warning System (BeltAlert) will be reactivated if the
driver's
seat belt is unbuckled for more than 10 seconds and the vehicle speed is
greater than 5 mph (8 km/h).
The Enhanced Warning System (BeltAlert) can be enabled or disabled by your
authorized dealer or by following these steps:
NOTE: The following steps must occur within the first 60 seconds of the
ignition switch being turned to the ON or RUN position. Daimler Chrysler
does not recommend deactivating the Enhanced Warning System (BeltAlert).
1. Turn the ignition switch to the OFF position, and buckle the driver's
seat belt.
2. Turn the ignition key to the RUN position (engine does not need to be
running), and wait for the Seat Belt Warning Light to turn off.
3. Within 60 seconds, unbuckle and then re-buckle the driver's seat belt
at
least three times, ending with the seat belt buckled.
4. Turn the ignition key to the OFF position. A single chime will sound to
signify that you have successfully completed the programming.
The Enhanced Warning System (BeltAlert) can be reactivated by repeating
this
procedure.
NOTE: Although the Enhanced Warning System (BeltAlert) has been
deactivated,
the Seat Belt Warning Light will continue to illuminate while the driver's
seat belt remains unfastened.
A/C Recirculation Programming
The recirculation control is programmed to cancel the recirculation mode
when the ignition key is turned OFF and will reset to outside air mode
when
the ignition key is turned ON. The frequent use of outside air will help
keep odors from building up within the air conditioner-heater housing. It
is
recommended that the recirculation mode be used as little as possible,
especially in humid climates.
For hot and dry climates, or people who are allergic to pollen and find
frequent use of the recirculation mode necessary, the recirculation mode
can
be programmed to not automatically reset to the outside mode by using the
following procedures:
.. Turn the ignition switch to the OFF position.
.. Set the mode control to "PANEL".
.. Depress and hold in the "Rear Wipe/Wash" button.
.. Start the engine, and continue to hold in the "Rear Wipe/Wash" button
until the indicator light starts fla****ng repeatedly.
.. Press the recirculation button until the indicator light remains lit.
.. The selection will be stored when the ignition switch is turned OFF or
if
the "Rear Wipe/Wash" button is pressed.
If the recirculation indicator light is lit, the recirculation mode will
not
reset when the engine is started. If the recirculation indicator light is
not lit, the recirculation mode will reset to the outside air mode when
the
engine is started. The programmed status can be changed back and forth by
following the above mentioned procedure.
Automatic Climate Control
To provide you with maximum comfort in the automatic mode, during cold
start-ups the blower fan will remain off and "DELAY" will appear in the
front ATC display until the engine warms up. Also, an estimate of the time
remaining until the "DELAY" is over will appear periodically in the
display.
However, the fan will engage immediately if the defrost mode is selected
or
by rotating the blower control to any fixed blower speed.
This feature may be disabled using the following procedure:
.. Press and hold the Heated Rear Window and Auto LO buttons for 5
seconds.
.. The "DELAY" symbol will flash to indicate that the feature as been
disabled.
This feature may be enabled using the following procedure:
.. Press and hold the Heated Rear Window and Auto HI buttons for 5
seconds.
.. The "DELAY" symbol will flash to indicate that the feature as been
enabled.
Note: I am not telling anyone to do any of these. I am not responsible for
any problems that may arise from this. Use at your on discretion.
--
Disabled vehicle conversion www.wheelchairdriver.com
|
