"Burgerman" <burgerman@[EMAIL PROTECTED]
> wrote in message
news:r4Yzj.27$kN5.14@[EMAIL PROTECTED]
> "Bret Ludwig" <bretldwig@[EMAIL PROTECTED]
> wrote in message
> news:6329c19f-1c81-4c9d-b9d0-8546eb394f1a@[EMAIL PROTECTED]
> >
> >>
> >> > >> >> >> Does anyone no how to disable the automatic door locks
that
> >> > >> >> >> lock
> >> to
> >> > >> >> >> doors once you reach about 15mph on a 1993 Plymouth Grand
> >> Voyager?
> >> > > The
> >> > >> >> >> stupid things are driving me crazy, I use it to make
> >> > >> >> >> delievries
> >> and
> >> > >> >> >> have to keep unlocking the door every time I pull away
from
a
> >> stop.
> >>
> >> > >> >> >> Help please!!!
> >>
> >> > >> >> > A scan tool would be needed to go into the Body Control
Module
> >> > >> >> > to
> >> > > have
> >> > >> >> > this
> >> > >> >> > done.
> >>
> >> > >> >> > Glenn Beasley
> >> > >> >> > Chrysler Tech
> >>
> >> > >> >> Does it?
> >>
> >> > >> >> Im sure it tells you how in my haynes or handbook somewhere.
It
> >> > >> >> is
> >> > >> >> very
> >> > >> >> annoying so I will dig it out asap and check it out for
myself.
> >>
> >> > >> > Haynes Book!!! Are you kidding?
> >>
> >> > >> N. Its either in there or in the handbook! Somewhere. I am sure
I
> >> > >> read
> >> it
> >> > >> already...
> >>
> >> > > Its a customer Preference setting that was designed to be set by
a
> >> > > scan
> >> > > tool
> >> > > only.
> >>
> >> > > Glenn Beasley
> >> > > Chrysler Tech
> >>
> >> > When I think about it it may have said it was "turnoffable" but
that
> >> > you
> >> > should contact your dealer?
> >> > I was actually looking to find out how to program a third key for
my
> >> > 2007
> >> > Dodge Caravan. The details for that were there for sure,
> >>
> >> That's correct, Chrysler made it so that the owner would have to
bring
it
> >> in
> >> to the dealer to have the settings changed on the older model
vehicles
> >
> > Just disconnect the solenoid.
>
>
>
>
> I knew I read it somewhere!!!
>
> Here is how:
>
>
>
>
> The Automatic Door Locks can be enabled or disabled by performing the
> following procedure:
>
> 1. Close all doors and place the key in the ignition switch.
>
> 2. Cycle the ignition switch ON/OFF four times ending i in the OFF
position,
> (do not start the engine)
>
> 3. Within 10 seconds of the final cycle, press the interior driver's
door
> lock switch to the LOCK position.
>
> 4. A single chime will sound to signify that you have successfully
completed
> the programming.
>
> You can turn the feature back on by repeating the above mentioned
procedure
> or by performing the procedure in the Electronic Vehicle Information
Center
> (EVIC), Customer Programmable Features section on vehicles so equipped.
>
>
> ________________________________________________________________
>
>
>
>
>
>
> And a few more for fun!
>
> Customer Key Programming
>
> You can program new sentry keys to the system if you have two valid
sentry
> keys by performing the following procedure:
>
> 1. Cut the additional Sentry Key Transponder blank(s) to match the
ignition
> switch lock cylinder key code.
>
> 2. Insert the first valid key into the ignition switch and turn the
ignition
> switch ON for at least 3 seconds but no longer than 15 seconds. Turn the
> ignition switch OFF and remove the first key.
>
> 3. Insert the second valid key and turn the ignition switch ON within 15
> seconds. After ten seconds a chime will sound and the Theft Alarm Light
will
> begin to flash. Turn the ignition switch OFF and remove the second key.
>
> 4. Insert a blank Sentry Key into the ignition switch and turn the
ignition
> switch ON within 60 seconds. After 10 seconds a single chime will sound.
The
> Theft Alarm Light will stop fla****ng, turn on for 3 seconds; then turn
off.
>
> The new Sentry Key has been programmed. The Keyless Entry Transmitter
will
> also be programmed during this procedure.
> Repeat this procedure to program up to a total of 8 keys. If you do not
have
> a programmed sentry key, contact your dealer for details.
> NOTE: If a programmed key has been lost, see your dealer to have all
> remaining keys erased from the systems memory. The remaining keys must
then
> repro-grammed. This will prevent the lost key from starting your
vehicle.
> All vehicle keys must be taken to the dealer at the time of service to
be
> reprogrammed.
>
>
>
>
>
>
> The Remote Unlock Driver's Door 1st feature can be enabled or disabled
by
> performing the following procedure:
>
> 1. Press the UNLOCK button for 5 to 10 seconds.
>
> 2. While the UNLOCK button is pressed, (after 5 seconds) press the LOCK
> button. Release both buttons.
>
> The "Remote Unlock Driver's Door 1st" feature can be reactivated by
> repeating the above mentioned procedure or by performing the procedure
in
> the Electronic Vehicle Information Center (EVIC), Customer Programmable
> Features section on vehicles so equipped.
>
>
>
>
>
>
> If desired, the "Sound Horn On Lock" feature can be turned on and off by
> performing the following procedure:
>
> 1. Press the LOCK button for 5 to 10 seconds.
>
> 2. While the LOCK button is pressed (after 5 seconds), press the PANIC
> button. Release both buttons.
>
> The "Sound Horn On Lock" feature can be reactivated by repeating this
> procedure or by performing the procedure in the Electronic Vehicle
> Information Center (EVIC), Customer Programmable Features section on
> vehicles so equipped.
>
>
>
>
>
>
> To Turn Off "Flash Lights On Lock/Unlock" - If Equipped
>
> If desired, the "Flash Lights On Lock/Unlock" feature can be turned on
and
> off by performing the following procedure:
>
> 1. Press the LOCK button for 5 to 10 seconds.
>
> 2. While the LOCK button is pressed, (after 5 seconds) press the UNLOCK
> button. Release both buttons.
>
> The "Flash Lights On Lock/Unlock" feature can be reactivated by
repeating
> this procedure or by performing the procedure in the Electronic Vehicle
> Information Center (EVIC), Customer Programmable Features section on
> vehicles so equipped. The table below explains the Lamp Flash options.
>
>
>
>
>
>
> The Sliding Door Open Flash can be enabled or disabled by performing the
> following procedure:
>
> 1. Place the key in the ignition switch.
>
> 2. Cycle the ignition switch ON/OFF four times ending in the OFF
position,
> (do not start the engine)
>
> 3. Within 10 seconds of the final cycle, press the hazard switch.
>
> 4. A single chime will sound to signify that you have successfully
completed
> the programming.
>
> You can turn the feature back on by repeating the above mentioned
procedure
> or by performing the procedure in the Electronic Vehicle Information
Center
> (EVIC), Customer Programmable Features section on vehicles so equipped.
>
>
>
>
>
>
> Enhanced Driver Seat Belt Use Reminder System (BeltAlert)
>
> If the driver's seat belt has not been buckled within 60 seconds of
starting
> the vehicle and if the vehicle speed is greater than 5 mph (8 km/h), the
> Enhanced Warning System (BeltAlert) will alert the driver to buckle
their
> seat belt. The driver should also instruct all other occupants to buckle
> their seat belts. Once the warning is triggered, the Enhanced Warning
System
> (BeltAlert) will continue to chime and flash the Seat Belt Warning Light
for
> 96 seconds or until the driver's seat belt is buckled.
>
> The Enhanced Warning System (BeltAlert) will be reactivated if the
driver's
> seat belt is unbuckled for more than 10 seconds and the vehicle speed is
> greater than 5 mph (8 km/h).
>
> The Enhanced Warning System (BeltAlert) can be enabled or disabled by
your
> authorized dealer or by following these steps:
>
> NOTE: The following steps must occur within the first 60 seconds of the
> ignition switch being turned to the ON or RUN position. Daimler Chrysler
> does not recommend deactivating the Enhanced Warning System (BeltAlert).
>
> 1. Turn the ignition switch to the OFF position, and buckle the driver's
> seat belt.
>
> 2. Turn the ignition key to the RUN position (engine does not need to be
> running), and wait for the Seat Belt Warning Light to turn off.
>
> 3. Within 60 seconds, unbuckle and then re-buckle the driver's seat belt
at
> least three times, ending with the seat belt buckled.
>
> 4. Turn the ignition key to the OFF position. A single chime will sound
to
> signify that you have successfully completed the programming.
>
> The Enhanced Warning System (BeltAlert) can be reactivated by repeating
this
> procedure.
>
> NOTE: Although the Enhanced Warning System (BeltAlert) has been
deactivated,
> the Seat Belt Warning Light will continue to illuminate while the
driver's
> seat belt remains unfastened.
>
>
>
>
>
>
>
> A/C Recirculation Programming
>
> The recirculation control is programmed to cancel the recirculation mode
> when the ignition key is turned OFF and will reset to outside air mode
when
> the ignition key is turned ON. The frequent use of outside air will help
> keep odors from building up within the air conditioner-heater housing.
It
is
> recommended that the recirculation mode be used as little as possible,
> especially in humid climates.
>
> For hot and dry climates, or people who are allergic to pollen and find
> frequent use of the recirculation mode necessary, the recirculation mode
can
> be programmed to not automatically reset to the outside mode by using
the
> following procedures:
>
> . Turn the ignition switch to the OFF position.
>
> . Set the mode control to "PANEL".
>
> . Depress and hold in the "Rear Wipe/Wash" button.
>
> . Start the engine, and continue to hold in the "Rear Wipe/Wash" button
> until the indicator light starts fla****ng repeatedly.
>
> . Press the recirculation button until the indicator light remains lit.
>
> . The selection will be stored when the ignition switch is turned OFF or
if
> the "Rear Wipe/Wash" button is pressed.
>
> If the recirculation indicator light is lit, the recirculation mode will
not
> reset when the engine is started. If the recirculation indicator light
is
> not lit, the recirculation mode will reset to the outside air mode when
the
> engine is started. The programmed status can be changed back and forth
by
> following the above mentioned procedure.
>
>
>
>
>
>
> Automatic Climate Control
>
> To provide you with maximum comfort in the automatic mode, during cold
> start-ups the blower fan will remain off and "DELAY" will appear in the
> front ATC display until the engine warms up. Also, an estimate of the
time
> remaining until the "DELAY" is over will appear periodically in the
display.
> However, the fan will engage immediately if the defrost mode is selected
or
> by rotating the blower control to any fixed blower speed.
>
> This feature may be disabled using the following procedure:
>
> . Press and hold the Heated Rear Window and Auto LO buttons for 5
seconds.
>
> . The "DELAY" symbol will flash to indicate that the feature as been
> disabled.
>
> This feature may be enabled using the following procedure:
>
> . Press and hold the Heated Rear Window and Auto HI buttons for 5
seconds.
>
> . The "DELAY" symbol will flash to indicate that the feature as been
> enabled.
>
>
>
>
> Note: I am not telling anyone to do any of these. I am not responsible
for
> any problems that may arise from this. Use at your on discretion.
>
>
>
>
>
> --
>
> Disabled vehicle conversion www.wheelchairdriver.com
>
The problem with those Manuals is they are written for multiple year
vehicles. They didn't have Sentry/skim keys, remote unlock doors etc...
for
the 93 Mini van. In order to program Cust preferences it has to be done
with the DRB2 scan tool. OP was 93 mini van.
Glenn Beasley
Chrysler Tech
|
